How to Install Vinyl Floors Over Linoleum . If the linoleum is in good shape, with no missing or loose tiles, there is no need to remove it. Because doubling the floor tile can make the floor too thick for some door thresholds, installing a thinner tile, like vinyl tiles, can make the final installation smoother. Inspect the linoleum well. Your new tile job is only as good as the old one, so make sure there are no loose corners, loose tiles or missing areas in the linoleum. Clean the linoleum well. Remove any built- up wax or dirt that may interfere with the bond of the new tiles to the old. Let the floor dry completely. Lay out the vinyl tiles right on top of the linoleum where you will install them to help determine where they should lay and where the cuts should be made. Set the first tile in the center of the wall furthest from the door and the next tiles evenly out to each side. This will hide the cuts on the corners or edges of the room. Cut the tiles to fit the edges of the room with a vinyl tile cutter. Lay the vinyl tile on the plate of the cutter with the area you wish to cut lined up with the blade. Installing Floor Tile Over Vinyl Flooring. Depress the handle of the cutter as if it were a paper cutter to slice the tile. Double- check the tile's fit with the others in the dry layout before installing. The vinyl tiles must cover the old linoleum completely to help ensure a good installation. Spread vinyl tile adhesive over the old linoleum with a trowel and press the tiles into place in the pattern and layout you determined earlier. Work backwards out of the room to let the tiles dry. Top 10 Questions about Laminate Why Choose Laminate? Laminate flooring is one of the. You can also install laminate over existing floors made of wood, concrete. Vinyl Flooring; Vinyl Plank Flooring; Tile Flooring; Linoleum. The Home Depot Community. What that means is that over time, you can possibly have your vinyl floor tiles popping up. In the photo still from the how-to install vinyl tile video, you can see the tiles being set up. Installing Vinyl Tile Over Existing Vinyl Floor. Part of the series: Flooring Help. Just because you have existing vinyl floors in your home doesn't mean that you can't install new vinyl over top of it. Install vinyl tile over. How to Install Tile over Vinyl. Laying a tile floor over vinyl sheet flooring or vinyl tiles is a tricky installation that is not ever a first choice application. This type of installation is not an industry. Allow the adhesive to dry for 2. Roll a floor roller over the new vinyl tile floor. Floor rollers exert an enormous amount of pressure on the vinyl, which will help to bond it to the linoleum. Things You Will Need. Cleaning supplies. Vinyl tile cutter. Vinyl tile adhesive. Trowel. Floor roller. Tip. You can rent vinyl tile cutters and floor rollers and your local hardware store. Warning. If any linoleum is loose or missing, do not attempt to remove more or cover it with vinyl until a professional has assessed it for asbestos. About the Author. Sarabeth Asaff has worked in and has written about the home improvement industry since 1. She has written numerous articles on art, interior design and home improvements, specializing in kitchen and bathroom design. A member in good standing with the National Kitchen and Bath Association, Asaff has working knowledge of all areas of home design. Photo Credits. Jupiterimages/Photos. How to Install Vinyl Floor Tile Over Old Vinyl Tile. How to Install Vinyl Floor Tile Over Old Vinyl Tile. Installing vinyl composition tile (VCT) over existing vinyl floor tile is often safer than removing the original vinyl. Many old vinyl tiles, and the adhesive used to bind them, contain asbestos. The removal of asbestos- laced materials requires licensed, trained professionals to seal off the area after donning breathing apparatus and hazardous material suits for protection against airborne asbestos fibers. Cover undisturbed tiles with a layer of underlayment to provide a smooth, safe surface for the installation of new vinyl tile. Things Needed. Measuring tape. Tracing paper. Pencil crayons. Claw hammer or pry bar. Stud finder. Galvanized wood screws. Power driver. Circular saw. Coping saw. Plywood underlayment. Wood filler. Putty knife. Fine- grit sandpaper. Sanding block. Chalk line. Straight edge. Pneumatic stapler. Compressor. Narrow crown staples, 1/4- by 7/8- inch long. Utility knife. Knee pads. VCT latex adhesive. Notched trowel. VCT tiles. Heat gun. VCT cutter. Floor transition pieces. Acrylic floor sealer. Planning the Layout. Step 1. Measure the room and draw a plan to scale using 1/4- inch graph paper or floor plan software. Draw your tiles from the center out to the edges, where partial tile installation is less obvious. Step 2. Transfer your plan to a tracing paper grid and make several photocopies so that you can decide on color and design elements. Step 3. Color the photocopies using your pencil crayons until you arrive at a pattern and color you like. Step 4. Count the number of tiles in each color you will need for your design and add 1. Step 5. Take your plan to your local home improvement store so that the associates there can help you determine how much plywood underlayment you will require. Order your tile and take home your underlayment so that the plywood can adjust to the humidity level in your home before work begins. A day or two should suffice. Step 6. Pick up the tile and all the remaining items you need when your tile order arrives. Preparing the Tiling Surface. Step 1. Remove baseboards and carpet strips using your claw hammer or pry bar. Trim the door casing with your coping saw so your plywood and tile will fit underneath. Complete fine cuts with your utility knife. Measure, cut and lay out your plywood underlayment. Step 2. Locate floor joists using your stud finder. Drive screws through the plywood and existing tile directly into the joists beneath. This will eliminate squeaky floors. Step 3. Level uneven seams in the underlayment using wood filler and a putty knife. Sand the joints lightly and sweep or vacuum to remove dust and debris. Step 4. Locate the center point of your floor. Transfer your tile pattern to the underlayment using your straightedge and chalk line. Use a pencil and a straight edge to darken the lines. This will enable you to locate the marks through your clear, dried adhesive. Laying the Tile. Step 1. Apply the VCT latex adhesive to one half of the floor using your notched trowel. Allow the adhesive to dry and turn clear. You will have six hours to lay your tile at this point. Step 2. Complete the center section first and work toward the edges. Use full tiles in the center and partial tiles in less visible edge areas. Cut tiles using the VCT tile cutter for crisp, clean edges. Soften curled tiles with the heat gun as required. Clean excess glue from the tiled surface using a damp cloth. Allow 2. 4- hours for the first half of the floor to dry and set. Step 3. Complete the second half of the floor as described in the previous two steps. Allow the second half to dry for 2. Roll the floor with your rented 1. Step 4. Replace floorboards and install new transitions from your new floor to the adjacent floor areas. Step 5. Allow five days for the floor adhesive to fully cure. Clean the floor with a mild detergent. Apply several coats of acrylic floor sealer, allowing the sealer to dry thoroughly between applications. Warnings. All materials and tools are available for purchase or rental at most home improvement stores. Use rubber knee pads to ease the pressure on your knees while you are laying vinyl tile. Rent the roller after the floor has been completely installed. This will reduce rental hour costs. Warnings. Wear heavy leather gloves when handling and cutting tiles with your VCT cutter. Plan ahead for an exit strategy when laying tile. References. Hometime: Vinyl Tile. Family Handyman: How to Lay a Vinyl Tile Floor. Handyman Business: Installing a Vinyl Floor. Related Articles.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
October 2016
Categories |